kinsunny 
Nowadays, there are so many products of pentek water filter cartridge 10 micron in the market and you are wondering to choose a best one. You have searched for pentek water filter cartridge 10 micron in many merchants, compared about products prices & reviews before deciding to buy them.
You are in RIGHT PLACE.
Here are some of best sellings pentek water filter cartridge 10 micron which we would like to recommend with high customer review ratings to guide you on quality & popularity of each items.
13,585 Reviews Scanned
Pentek EPM-20BB Carbon Block Filter Cartridge, 20" x 4-5/8", 10 Microns
- none
- Imported
- Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water
- Nominal filtration rating of 10 microns
- Bonded PAC media with polyolefin pre-filter and polyethylene netting for extended life
- Initial pressure drop of 4 psi at a flow rate of 4 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
This Pentek EPM-20BB carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. It has a nominal (85%) filtration rating of 10 microns. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 90% in up to 30,000 gallons at a flow rate of 4 gallons per minute (gpm). This cartridge is made of bonded powdered activated carbon (PAC) filter media wrapped in polyolefin with polyethylene outer netting. The nitrile butadiene rubber (Buna-N) gaskets seal the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 4 pounds per square inch (psi) at a flow rate of 4 gallons per minute (gpm), and operates over a temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C). This carbon block filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for purification of residential and commercial drinking water.
Specifications
| Nominal filtration rating | 10 microns |
| Initial pressure drop at 4 gpm | 4 psi |
| Chlorine reduction capacity | 30,000 gallons at 4 gpm |
| Temperature range | 40 to 180 degrees F (4.4 to 82.2 degrees C) |
| Maximum dimensions (H x W) | 20 x 4-5/8 inches (508 x 118 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 90%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Pentek EPM-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 10 Microns
- Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water
- Nominal filtration rating of 10 microns
- Bonded PAC media with polyolefin pre-filter and polyethylene netting for extended life
- Initial pressure drop of 1.5 psi at a flow rate of 1 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
This Pentek EPM-10 carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. It has a nominal (85%) filtration rating of 10 microns. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 90% in up to 3,000 gallons at a flow rate of 1 gallon per minute (gpm). This cartridge is made of bonded powdered activated carbon (PAC) filter media wrapped in polyolefin with polyethylene outer netting. The nitrile butadiene rubber (Buna-N) gaskets seal the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 1.5 pounds per square inch (psi) at a flow rate of 1 gallon per minute (gpm), and operates over a temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C). This carbon block filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for purification of residential and commercial drinking water.
Specifications
| Nominal filtration rating | 10 microns |
| Initial pressure drop at 1 gpm | 1.5 psi |
| Chlorine reduction capacity | 3,000 gallons at 1 gpm |
| Temperature range | 40 to 180 degrees F (4.4 to 82.2 degrees C) |
| Maximum dimensions (H x W) | 9-3/4 x 2-7/8 inches (248 x 73 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 90%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Similar items with 4 stars and above
Pentek DGD-5005 Spun Polypropylene Filter Cartridge, 10" x 4-1/2"
- Reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water
- Combines two separate gradient layers for higher efficiency and dirt-loading capacity
- Spun polypropylene for resistance to chemicals and bacteria
- Initial pressure drop of less than 1 psi at a flow rate of 10 gpm
- Temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C).
This Pentek DGD-5005 spun polypropylene filter cartridge reduces sand, silt, scale, and rust particles in residential, commercial, and municipal drinking water. It has two separate gradient layers for higher particle reduction efficiency and dirt-loading capacity than standard spun or string-wound cartridges. The nominal filtration rating of the pre-filter layer is 50 microns, and the rating of the post-filter layer is 5 microns. The filter is made of spun polypropylene fibers for resistance to chemicals and bacteria. It has an initial pressure drop of less than 1 pound per square inch (psi) at a flow rate of 10 gallons per minute (gpm), and operates over a temperature range of 40 to 145 degrees F (4.4 to 62.8 degrees C). This spun polypropylene filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for treatment of residential, commercial, and municipal drinking water.
Specifications
| Nominal filtration rating (pre-filter) | 50 microns |
| Nominal filtration rating (post-filter) | 5 microns |
| Initial pressure drop at 10 gpm | <1> |
| Temperature range | 40 to 145 degrees F (4.4 to 62.8 degrees C) |
| Maximum dimensions (H x W) | 10 x 4-1/2 inches (254 x 114 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek CBC-10 Carbon Block Filter Cartridge, 9-3/4″ x 2-7/8″, 0.5 Micron
- Reducesfine sediment, chlorine taste and odor, and protozoan cysts in residential and commercial drinking water
- Nominal filtration rating of 0.5 micron
- Bonded PAC media with polyolefin wraps and polyethylene netting
- Initial pressure drop of 3.7 psi at a flow rate of 2 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
Pentek R50-BB Pleated Polyester Filter Cartridge, 9-3/4″ x 4-1/2″, 50 Microns
- Reduces sand, dirt, silt, rust, and scale particles in residential and commercial water
- Nominal filtration rating of 50 microns
- Non-woven polyester media pleated around a polypropylene core for strength
- Initial pressure drop of less than 1 psi at a flow rate of 10 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
Pentek EP-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 5 Microns
- Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water
- Nominal filtration rating of 5 microns
- Bonded PAC media with polyolefin pre-filter and polyethylene netting for extended life
- Initial pressure drop of 3.4 psi at a flow rate of 1 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
This Pentek EP-10 carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. It has a nominal (85%) filtration rating of 5 microns. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 90% in up to 6,000 gallons at a flow rate of 1 gallon per minute (gpm). This cartridge is made of bonded powdered activated carbon (PAC) filter media wrapped in a polyolefin pre-filter with polyethylene outer netting. The nitrile butadiene rubber (Buna-N) gaskets seal the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 3.4 pounds per square inch (psi) at a flow rate of 1 gallon per minute (gpm), and operates over a temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C). This carbon block filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for purification of residential and commercial drinking water.
Specifications
| Nominal filtration rating | 5 microns |
| Initial pressure drop at 1 gpm | 3.4 psi |
| Chlorine reduction capacity | 6,000 gallons at 1 gpm |
| Temperature range | 40 to 180 degrees F (4.4 to 82.2 degrees C) |
| Maximum dimensions (H x W) | 9-3/4 x 2-7/8 inches (248 x 73 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 90%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek EPM-BB Carbon Block Filter Cartridge, 9-3/4" x 4-5/8", 10 Microns
- Reduces fine sediment and chlorine taste and odor in residential and commercial drinking water
- Nominal filtration rating of 10 microns
- Bonded PAC media with polyolefin pre-filter and polyethylene netting for extended life
- Initial pressure drop of 5 psi at a flow rate of 2 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
This Pentek EPM-BB carbon block filter cartridge reduces fine sediment and chlorine taste and odor in residential and commercial drinking water. It has a nominal (85%) filtration rating of 10 microns. The filter will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 90% in up to 15,000 gallons at a flow rate of 2 gallons per minute (gpm). This cartridge is made of bonded powdered activated carbon (PAC) filter media wrapped in polyolefin with polyethylene outer netting. The nitrile butadiene rubber (Buna-N) gaskets seal the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 5 pounds per square inch (psi) at a flow rate of 2 gallons per minute (gpm), and operates over a temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C). This carbon block filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 42 for quality assurance, and is used for purification of residential and commercial drinking water.
Specifications
| Nominal filtration rating | 10 microns |
| Initial pressure drop at 2 gpm | 5 psi |
| Chlorine reduction capacity | 15,000 gallons at 2 gpm |
| Temperature range | 40 to 180 degrees F (4.4 to 82.2 degrees C) |
| Maximum dimensions (H x W) | 9-3/4 x 4-5/8 inches (248 x 118 mm) |
| Materials certification | NSF/ANSI standard 42 |
The nominal filtration rating is for a particle removal efficiency of 85%. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 90%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek FloPlus-10 Carbon Block Filter Cartridge, 9-3/4" x 2-7/8", 0.5 Micron
- Reduces fine sediment, chlorine taste and odor, and protozoan cysts in high-flow residential and commercial drinking water applications
- Nominal filtration rating of 0.5 micron
- Modified bonded PAC media combines efficient cyst reduction with the high flow rate of a 10-micron filter
- Initial pressure drop of 2 psi at a flow rate of 1 gpm
- Temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C)
This Pentek FloPlus-10 carbon block filter cartridge reduces fine sediment, chlorine taste and odor, and protozoan cysts in residential drinking water. It has a nominal (85%) filtration rating of 0.5 micron, and 99.95% efficiency for the reduction of protozoan cysts. It will reduce free available chlorine (FAC) at 2 parts per million (ppm) by at least 90% in up to 10,000 gallons at a flow rate of 1 gallons per minute (gpm). This cartridge is made of modified bonded powdered activated carbon (PAC) filter media that provides efficient cyst reduction with a flow rate and dirt-holding capacity comparable to those of a 10-micron filter. The Santoprene (TPE, thermoplastic elastomer) gaskets seal the cartridge against the housing (sold separately). The cartridge has an initial pressure drop of 2 pounds per square inch (psi) at a flow rate of 1 gallon per minute (gpm), and operates over a temperature range of 40 to 180 degrees F (4.4 to 82.2 degrees C). This carbon block filter cartridge meets National Sanitation Foundation/American National Standards Institute (NSF/ANSI) standard 53 for quality assurance, and is used for purification of residential and commercial drinking water.
Specifications
| Nominal filtration rating | 0.5 microns |
| Initial pressure drop at 1 gpm | 2 psi |
| Removal of protozoan cysts | 99.95% |
| Chlorine reduction capacity | 10,000 gallons at 1 gpm |
| Temperature range | 40 to 180 degrees F (4.4 to 82.2 degrees C) |
| Maximum dimensions (H x W) | 9-3/4 x 2-7/8 inches (248 x 73 mm) |
| Cyst reduction certification | NSF/ANSI standard 53 |
The nominal filtration rating is for a particle removal efficiency of 85%. Protozoan cysts include Giardia, Entamoeba, Cryptosporidium, and Toxoplasma. Chlorine reduction capacity is the minimum total amount of water for which the free available chlorine (FAC) at a concentration of 2 ppm is reduced by at least 90%.
H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back.
Water filters remove undesirable particles, chemicals, and microorganisms from water by means of a semipermeable barrier, adsorption, or biological processes. They are made of densely packed synthetic or natural fibers that trap suspended particles, materials that block microbes or adsorb unwanted chemicals, or substances that cause a chemical change, such as acid neutralization. For most residential, commercial, and industrial applications, water filters are manufactured in the form of replaceable cartridges that fit inside permanent housings. Filtration systems typically consist of a series of two or more types of filters, each designed to remove different contaminants. The performance of filters is measured by the minimum particle size that is blocked, the percentage of particles or microorganisms that are removed, the downstream concentration of unwanted chemicals, the maximum flow rate, and the amount of water that can be filtered before the filter must be replaced. Water filters are used in a wide range of applications, including drinking water purification, swimming pools, industrial processes, and irrigation, among others.
Pentair manufactures industrial, commercial, and residential water filtration components and systems. The company, founded in 1966 and headquartered in Minneapolis, MN, meets International Organization for Standardization (ISO) standards 9001 and 14001 for quality assurance.
Pentek RFC20-BB Carbon Filter Cartridge, 20" x 4-1/2"
- Reduces chlorine taste and odor in drinking water
- Granular activated carbon (GAC) media with spun polypropylene core and polypropylene end caps for strength
- Porous polyethylene 70-micron outer shell reduces carbon fines and other particles
- Initial pressure drop of 0.90 psi at a flow rate of 4 gpm
- Temperature range of 40 to 125 degrees F (4.4 to 51.7 degrees C)
Pentek R50-BB 50 Micron 10 x 4.5 Whole House Pleated Sediment Filter 12 Pack
Our Promise to Readers
We keep receiving tons of questions of readers who are going to buy pentek water filter cartridge 10 micron, eg:
- What are Top 10 pentek water filter cartridge 10 micron for 2020, for 2019, for 2018 or even 2017 (old models)?
- What is Top 10 pentek water filter cartridge 10 micron to buy?
- What are Top Rated pentek water filter cartridge 10 micron to buy on the market?
- or even What is Top 10 affordable (best budget, best cheap or even best expensive!!!) pentek water filter cartridge 10 micron?…
- All of these above questions make you crazy whenever coming up with them. We know your feelings because we used to be in this weird situation when searching for pentek water filter cartridge 10 micron.
- Before deciding to buy any pentek water filter cartridge 10 micron, make sure you research and read carefully the buying guide somewhere else from trusted sources. We will not repeat it here to save your time.
- You will know how you should choose pentek water filter cartridge 10 micron and What you should consider when buying the pentek water filter cartridge 10 micron and Where to Buy or Purchase the pentek water filter cartridge 10 micron. Just consider our rankings above as a suggestion. The final choice is yours.
- That’s why we use Big Data and AI to solve the issue. We use our own invented, special algorithms to generate lists of Top 10 brands and give them our own Scores to rank them from 1st to 10th.
- You could see the top 10 pentek water filter cartridge 10 micron of 2020 above. The lists of best products are updated regularly, so you can be sure that the information provided is up-to-date.
- You may read more about us to know what we have achieved so far. Don’t hesitate to contact us if something’s wrong or mislead information about pentek water filter cartridge 10 micron.
Conclusion
By our suggestions above, we hope that you can found pentek water filter cartridge 10 micron for you.Please don’t forget to share your experience by comment in this post. Thank you!
