The 9 Best Fuel Filter Water Seperator

If you have difficulty in installing, you can go to YouTube to find the appropriate installation video:https://www.youtube.com/watch?v=LyeqTDVzY-A.

Specification:
1.Fuel Water Separating Filter fit 3/8 Inch NPT Outboard Motors as well.
2.Maximum Flow Rate 30 GPH (57 LPH).
3.Port / Connecting Size M18 X 1.5 Center Thread.
4.These are more suited to compact off road diesel equipment:tractors,skid steers loaders,movers.
5.Filter Rating 10 Micron.10 micron filters are over 90% efficient at removing particles as small as 10 microns. 10 micron filters are recommended to prevent damage to sensitive inboard, sterndrive and outboard fuel injection systems, Designed to trap the smallest particles and emulsified water from Diesel.

Product details:
1.Don’t be caught in the water without one of these Diesel spin-on filters.
2.Filters are designed for high performance applications, and with flow rate of 30 GPH on the R12T model, your engine will perform better than ever with clean, water-free Fuel.
3.The inlet and out let can be feed in on the same side or in one side out the other side.
4.Check and replace regularly.

R12T water separator and filter complete combo installation instruction:
1.Nylon collection bowl down when installed the water separator and filter.
2.This filter has four ports, two inputs and two outputs. We provide two plugs for the extra two ports. If you need to use two plugs, you must install them to the filter and tighten them.
3.Before installing the filter, you have to remove those plugs, teflon-tape them, and re-install them.Prevent leaks from these plugs.
4.All of the above steps are very simple to operate, you can manually disassemble, and then use the tool to install tighten.

Sierra fuel water separators remove over 99.8% of emulsified water from your gasoline. Sierra’s 10 micron filters are over 90% efficient at removing particles as small as 10 microns. All filters flow @ 90 GPH to feed even the hungriest motor. Sierra 10 micron filters are recommended to prevent damage to sensitive inboard, sterndrive and outboard fuel injection systems.

WATER-BLOCK filter removes water from gasoline and diesel fuel. Water-absorbing polymers trap water, restricting fuel flow when it is time to replace the element. Also removes microscopic particles (17 microns) of rust, sand, dirt, scale and lint. Also compatible with biodiesel blends up to 20%. Zinc die-cast top cap with 3/4 inch NPT pipe fittings. See-Thru bowl allows for visual monitoring of fuel flow. Maximum recommended flow rate is 25 gpm. Gravity flow rate is approximately 5 gpm with a 24 inch head. Working pressure up to 150 psi.

The Moeller 033320-10 10 Micron Water Separating Filter Kit is designed for Mercury, Johnson, Evinrude, Yamaha, Suzuki, Honda, Tohatsu and Nissan engines, along with universal applications. Includes a powder coated reusable filter head, filter, barbs and plugs. Not recommended for use with electric fuel pumps.

Item specifics:
PRODUCT TYPE : Filter Fuel/water Separator
-This listing is for one (1) unit. This is a new For Racor R12T Marine Fuel Filter / Water Separator complete assembly.
Product Type Filter Fuel/Water Separator
Description Replacement Fuel Filter/Water Separator
-Maximum Flow Rate 15 GPH (57 LPH)
-Filter Rating 10 Micron
-Port/Connecting Size M18 X 1.5 Center Thread
-Additional Detail Used In Model 120A Filter Assembly
Dont’ be caught in the water without one of these diesel spin-on filters. filters are designed for high performance applications, and with flow rate of 15 GPH on the R12T model, your engine will perform better than ever with clean, water-free fuel. These filter units are coated with a durable electrostatically applied powder coating for superior corrosion resistance. The unit features Racor’s famous Aquabloc II technology. This spin-on filter design is simple to replace and the reusable clear plastic collection bowl and features a self-venting drain for removing unwanted muck and water.

Please Check the part number and our fitment before placing order. Professional installation recommended!

Features:

● Durable Fuel & Water Separator provides excellent water removal over the life of the filter.

● Pleated paper filtering media ensures lower flow restriction and higher dirt holding capacity.

● Direct fit and easy installation. All parts and components needed are included, great replacement for your old one!

● Top quality and powerful function making this kit an ideal choice as gift for your friends, family members, neighbors, etc,.

● This fuel filter set provides the best defense for sensitive fuel system components and enhance engine performance by filter the harmful contaminants.

Specifications:

● Item Type: Fuel Filter/ Oil Filter/ Fuel &Water Separator

● OEM Part Number: 68197867AB / 68157291AA / 5083285AA / FS43255 / 68065608AA / FS53000

Applications:

● 2013 2014 2015 2016 2017 2018 Dodge Ram 2500 6.7 Cummins Diesel Fuel Filter

● 2013 2014 2015 2016 2017 2018 Dodge Ram 3500 6.7 Cummins Diesel Fuel Filter

● 2013 2014 2015 2016 2017 2018 Dodge Ram 4500 6.7 Cummins Diesel Fuel Filter

● 2015 2016 2017 2018 Dodge Ram 5500 6.7 Cummins Diesel Fuel Filter

Tips: Fuel filter is one of the key components in protecting the engine from hazardous foreign particles, it is important to replace it regularly 🙂

Buy with Confidence. Our products are backed by an uncompromising level of technical support and after sales service. Any question? Please don’t hesitate to contact us!

Sierra 18-7945 10 Micron Fuel Water Separating Filter for Mercury/MerCruiser and Yamaha

DETAILS
• Sierra Fuel Water Separators Remove over 99.8% of Emulsified Water from your Gasoline • Over 90% Efficient at Removing Particles as small as 10 Micron AND Flow at 90 GPH to Feed even the Hungriest Motor
• Sierra 10 Micron Filters are Recommended to prevent Damage to Sensitive Inboard, Sterndrive and Outboard Fuel Injection Systems
• Replaces: Mercury/MerCruiser 35-802893Q01, 35-604941, 35-60494, 35-55501, 35-57250, 35-60494A5, 35-806771, 35-8052691, 35-802893Q, 35-807172 and Yamaha ABB-FUELF-IL-TR
• Filter Size: Long – 4.35″ or 110.5mm
• Rating: 10 Micron
• Flow: 90 GPH

ABOUT SIERRA
Sierra is dedicated to protecting you and your investment. For 50 years Sierra, one of the most trusted names in the marine industry, has proudly been offering high quality engine and drive parts. Their products meet or exceed the original equipment part it replaces and are engineered to meet today’s high horsepower engine demands while withstanding the harsh marine environment.

SIERRA’S CUSTOMER SATISFACTION WARRANTY
All Sierra parts qualify for Sierra’s Industry Leading Customer Satisfaction Warranty. Sierra warrants its products to be free of defects in workmanship and materials for the useful life of the product. If a Sierra product fails to comply with the warranty, Sierra will repair or replace the defective product free of charge. The warranty is subject to additional terms, conditions and limitations. You can view Sierra’s full warranty located above in the Technical Specification Section.

Replaces Mercury 35-60494-1.
Replaces Racor S3213, B32013,18-7932-1,18-7932,18-7928-1,18-7928.
Filter Replaces Mercury Marine 35-809097,Racor S3213,Yamaha MAR-24563-03-00,18-7919,18-7919-1.

To replace element:
1.Drain the unit by loosen the drain screw.
2.Loosen and remove the filter element.
3.Loosen and remove the bowl from filter element.Please note the bowl is reusable,do not dispose unless broken.
4.Wipe O-ring gland clean,and coat bowl’s seal O-ring with fresh oil or grease and place it back to the gland.Then tighten the bowl onto filter element firmly by tool.
5.Coat filter element’s seal O-ring with fresh oil or grease and attach filter element onto filter head,and the tighten securely by tool.
6.Run engine and check for fuel leakage.

Attention:
1.Make sure you remove both the filter and the filter bowl from the mounting housing and put a light film of fuel on the o-ring.As delivered it will leak without the lubrication to allow for the proper crush.
2.For diesel transfer tank to filter the fuel before it enters the main tank.Only thing is you have to make sure to get the proper sealant for the threads. For The First time installation,in order to avoid any leaking at the threads.You’d better get some thread paste since the tape might plug the injectors if it were to come loosen.
3.Check and replace regularly.

Instructions:
To Drain Water:
1.Loosen drain screw to drain bowl of water.
2.Tighten drain screw.
3.Run engine and check for fuel leakage.

Safety Warning:
Periodically check fittings and filter element for leaks.Be careful when changed fuel filter element.Diesel is extremely flammable and highly explosive under certain conditions.Avoid spilling diesel.Always stop engine and do not smoke or allow open flames in the area while changing filter element.

Check out these genuine Yamaha MAR-FUELF-IL-TR Fuel/Water Separating Filters. When it comes to the lifeblood of your recreational vehicle, why take chances with a substitute manufacturer? Give your investment the protection it deserves with authentic Yamaha outboards. *Yamaha outboard models of 115 HP or less may require the MAR-MINIF-IL-TR Fuel/Water Separating filter. This is completely up to the boat manufacturer and dependent on available space in the boats transom. If you are unsure, please check your current set-up before purchasing. Thanks!

Conclusion

By our suggestions above, we hope that you can found fuel filter water seperator for you.Please don’t forget to share your experience by comment in this post. Thank you!